Updated Nov 20, 2026· 10 min read

Key takeaways

  • Compare the best jointers for brick and block work, from barrel and ball jointers to convex and bucket handle picks, with sizes, materials and lengths.
⭐ Key Takeaways
Quick answer: Our top pick is Bon Tool Barrel Jointer (21-760), with OX Pro Brick Jointer (OX-P031104) as a strong alternative.

The best jointer for most brick and block work is the Bon Tool Barrel Jointer (21-760), because its cast aluminum body carries four replaceable steel barrels that cover 1/2 inch, 5/8 inch, 3/4 inch and 7/8 inch joints with one tool. For smaller joints, the OX Pro Brick Jointer handles 3/8 inch and 1/2 inch work in alloy steel, while the Bon Tool Ball Jointer, the Roughneck Ding’er bucket handle jointer and an unbranded barrel jointer round out the list for wide joints, bucket handle fans and tight budgets.

A jointer is the hand tool drawn along fresh mortar to compact it and give the joint its finished profile. Tooling does more than tidy the wall: a well compacted concave joint sheds water, seals the surface of the mortar and keeps the joint line even from one end of the wall to the other. The five picks below cover the main jointer families a mason or homeowner is likely to need, from double ended convex bars to interchangeable barrel systems, and each one is matched to the joint sizes it is published to fit.

As an Amazon Associate, we earn from qualifying purchases.

Table of Contents

  • How to Choose the Right Jointer
  • The Best Jointers
  • Frequently Asked Questions
  • Conclusion
  • Product and ASIN Reference

How to Choose the Right Jointer

Match the tool size to the joint

The working rule is to use a jointer slightly larger than the joint itself. A tool that is too small sinks down into the mortar and leaves a deep, narrow groove with weak compaction at the edges, while a tool close to the joint width rides on the faces of the brick or block and presses the mortar into a dense, even profile. Standard brickwork commonly uses 3/8 inch joints, so a 1/2 inch jointer is the usual pick for that work, and wider rustic joints call for 5/8 inch, 3/4 inch or 7/8 inch tools. Double ended jointers carry two sizes on one bar, which saves swapping tools between bed joints and head joints of different widths.

Pick the profile the wall needs

The concave profile, formed by convex and barrel jointers, is the most common finish on exterior brickwork because its pressed, curved surface sheds rain and resists erosion. A V jointer cuts a sharp angled groove that suits some modern and decorative work. A grapevine jointer leaves a shallow joint with a thin raised or indented line along the middle, a finish linked with older hand tooled masonry. Raked joints, where mortar is taken back from the face, are produced with a joint raker rather than a finishing jointer, and they belong on sheltered walls because the recessed mortar holds water on exposed faces.

Consider material and build

Most hand jointers are made from high carbon steel, alloy steel or hardened steel, and the working edges take constant abrasion from sand in the mortar, so harder steel holds its profile longer. Barrel jointers take a different approach: a cast aluminum body holds replaceable steel barrels, so a worn working surface is swapped rather than the whole tool being replaced. Ball jointers and bucket handle jointers use a single rounded working head, often paired with a wood handle, and suit short runs, patching and head joints where a long bar is awkward.

Hand jointers and long runners

Short hand jointers handle head joints, short runs and tight spots around openings. Long sled runners, which mount a jointer blade on a handle so it spans several bricks at once, bridge small differences in unit size and keep long bed joints straight. A common crew setup pairs a short jointer and a longer runner in the same profile and width so that bed joints and head joints match across the wall. All five picks in this guide are hand jointers, which is the format most homeowners and small crews reach for first.

Tool at the right moment

Mortar is ready to tool when it is thumbprint hard: firm enough to hold a thumb impression without smearing wet paste across the face of the brick. Tooling too early draws water and fines to the surface and weakens the joint, while tooling too late leaves dark burn marks where the tool drags across mortar that has already set. Work the head joints and bed joints in a steady order so the whole wall is struck at a similar stage of firmness.

The Best Jointers

1. Bon Tool Barrel Jointer (21-760)

Bon Tool Barrel Jointer (21-760)

Bon Tool Barrel Jointer (21-760)

Check price on Amazon

The Bon Tool Barrel Jointer is the premium pick in this group and the most flexible, because one cast aluminum body accepts replaceable steel barrels in four sizes. The barrel set covers 1/2 inch, 5/8 inch, 3/4 inch and 7/8 inch joints, which spans nearly every joint width found in brick, block and stone work, so a single tool handles a full day of mixed work without a trip back to the toolbox. When a barrel wears, it is replaced on its own, which keeps the working profile crisp over years of use.

Barrel jointers roll and press the mortar rather than dragging a fixed edge through it, and many masons find the action leaves a clean concave finish with less pulling at the edges of the joint. The cast aluminum body keeps the tool light in the hand for a tool of its coverage, and the barrel format is a long established professional pattern rather than a novelty design. For anyone laying brick regularly, or a homeowner facing a full chimney or garden wall rebuild, this is the jointer that covers the most ground.

Specs

  • Joint sizes: 1/2 in, 5/8 in, 3/4 in and 7/8 in, from four replaceable steel barrels
  • Body material: Cast aluminum
  • Barrel material: Steel
  • Model: 21-760
  • Tier: Premium

2. OX Pro Brick Jointer (OX-P031104)

OX Pro Brick Jointer (OX-P031104)

OX Pro Brick Jointer (OX-P031104)

Check price on Amazon

The OX Pro Brick Jointer is a mid-range double ended bar jointer sized for the smaller end of the range, with 3/8 inch and 1/2 inch working ends. That pairing suits standard brick joints and the narrower joints found on brick slips and veneer work, where the wider tools in this guide would ride too high on the unit faces. The bar is alloy steel, and the listed dimensions of 8 x 7.5 x 33 cm with a weight of 120 g describe a slim, light tool that carries easily in a tool belt or bucket.

Double ended bars like this one are the format most bricklayers learn on: one end forms the joint, the other end covers the next size up, and the cranked shape keeps knuckles clear of the wall face while the tool is drawn along. The OX Pro line is the trade range from OX Tools, and this model, the OX-P031104, is the 10 x 13 mm size in that range. It is a sensible main jointer for anyone whose work sits in the 3/8 inch to 1/2 inch band.

Specs

  • Joint sizes: 3/8 in and 1/2 in (10 x 13 mm)
  • Material: Alloy steel
  • Listed dimensions: 8 x 7.5 x 33 cm
  • Weight: 120 g
  • Model: OX-P031104
  • Tier: Mid-range

3. Bon Tool Ball Jointer (21-182)

Bon Tool Ball Jointer (21-182)

Bon Tool Ball Jointer (21-182)

Check price on Amazon

The Bon Tool Ball Jointer, model 21-182, takes a simpler approach: a single 7/8 inch ball head on a wood handle. The rounded ball head presses a smooth concave profile into wide joints and is forgiving on short runs, patch repairs and head joints, where the round head can be worked into corners and short vertical joints that a long bar handles poorly. The wood handle gives a warm, familiar grip that many masons prefer for detail work.

At 7/8 inch, this is a wide joint tool, suited to rustic brickwork, blockwork with generous joints and stone work where narrower jointers would sink into the joint and tear the surface. It is a mid-range, single purpose tool rather than a system: there are no sizes to swap and nothing to adjust, which is exactly the appeal for repair work. Keep it alongside a narrower bar jointer and the pair covers wide and standard joints between them.

Specs

  • Joint size: 7/8 in
  • Handle: Wood
  • Model: 21-182
  • Tier: Mid-range

4. Roughneck Ding’er Bucket Handle Brick Jointer (ROU51035)

The Roughneck Ding’er is a bucket handle jointer, a style named for the rounded bucket handle profile it presses into the mortar. This model, the ROU51035, is a single size tool for 16 mm joints, which is 5/8 inch, one of the most common widths in blockwork and wider brick joints. The listed dimensions are 34.5 x 11 x 6 cm and the listed weight is 170 g, so it is a full length hand tool with enough presence to track steadily along a bed joint.

Bucket handle joints give a deep, rounded concave finish that reads clearly on the wall and sheds water well, and the single head format keeps the tool simple and budget friendly. Roughneck positions the Ding’er as a working site tool rather than a polished presentation piece, and the silver finish and one piece format match that role. For a homeowner repointing a garden wall with 5/8 inch joints, or a mason who wants a dedicated bucket handle tool without paying for a multi size system, this is the straightforward pick.

Specs

  • Joint size: 16 mm (5/8 in)
  • Style: Bucket handle (Ding’er)
  • Listed dimensions: 34.5 x 11 x 6 cm
  • Weight: 170 g
  • Model: ROU51035
  • Tier: Budget

5. Barrel Jointer with 7/8 and 3/4 Inch Barrels and Two Extra Blades

Check price on Amazon

This unbranded barrel jointer follows the classic assembled barrel pattern: it arrives assembled with 7/8 inch and 3/4 inch barrels fitted and two extra blades in the box, so the two most common wide joint sizes are covered from the first day and replacements are already on hand when a barrel wears. The listing gives the manufacturer simply as a generic maker, and the listing data does not publish a barrel material or an overall length, so those details are left unstated here rather than assumed.

As a budget route into the barrel format, it makes sense for occasional work: a chimney repair, a short run of rustic brickwork, or a first attempt at wide concave joints before committing to a premium brand system. The trade off is the unknown specification. Buyers who lay brick every week will be better served by the Bon Tool barrel system above, with its four published sizes and named maker, but for light and occasional use this set covers the wide sizes at the lowest commitment in the group.

Specs

  • Joint sizes: 7/8 in and 3/4 in
  • Included: Assembled jointer with both barrels, plus 2 extra blades
  • Material: Not stated in the listing
  • Brand: Unbranded
  • Tier: Budget

Frequently Asked Questions

What size jointer do I need for a standard brick joint?

Standard brickwork is usually laid with a 3/8 inch joint, and the working rule is to tool it with a jointer slightly larger than the joint, so a 1/2 inch jointer is the common choice. The OX Pro in this guide covers that pairing directly with its 3/8 inch and 1/2 inch ends. For wider joints, match the tool the same way: a 5/8 inch jointer for joints a step below that width, and 3/4 inch or 7/8 inch tools for the widest rustic work.

What is the difference between a barrel jointer and a convex jointer?

A convex jointer is a fixed bar, usually double ended, whose rounded edges press a concave profile into the mortar as it is drawn along the joint. A barrel jointer holds round steel barrels in a body, and the barrels can be swapped for other sizes or replaced when worn, so one handle covers several joint widths. Both produce a concave finish; the barrel format adds size range and replaceable working parts, while the fixed bar is simpler and slimmer.

When is mortar ready to be tooled with a jointer?

Mortar is ready when it reaches thumbprint hard: press a thumb into the joint and it should hold the impression cleanly without wet mortar smearing onto the brick face. Tooling before that point pulls water and fine material to the surface and weakens the joint, and tooling after the mortar has set hard leaves dark drag marks and a rough finish. On warm, windy days the window arrives sooner, so check a shaded and a sunny section of wall separately.

Can one jointer finish both bed joints and head joints?

Yes, a short hand jointer can strike both the horizontal bed joints and the vertical head joints, and double ended and barrel jointers do this routinely on small and medium work. The head joints are shorter and tighter, so a compact tool with a size matched to the joint is easier to control there. On long walls, crews often add a long sled runner in the same width for the bed joints to keep them straight, and use the hand jointer for the head joints.

Conclusion

For most buyers, the Bon Tool Barrel Jointer (21-760) is the jointer to own: four replaceable steel barrels in a cast aluminum body cover 1/2 inch through 7/8 inch joints, and worn barrels swap out instead of retiring the tool. If your work sits in the standard 3/8 inch to 1/2 inch band, the OX Pro Brick Jointer is the leaner mid-range choice, and the Bon Tool Ball Jointer adds a dedicated wide joint head for repair work. The Roughneck Ding’er covers 5/8 inch bucket handle joints on a budget, and the unbranded barrel set is the low commitment way to try the barrel format on wide joints. Whichever format you choose, match the tool size to a step above the joint width and tool the mortar at thumbprint hard, and the finished joints will stay dense, even and weather resistant.

D
Dũng Trọc Hà Đông
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Jointers for Brick and Mortar Work: Top…Check price on Amazon