Key takeaways
- See what the DC HOUSE 12-inch linear actuator offers: 1000N of push and pull force, 14 mm/s travel speed, IP54 sealing and mounting brackets included.
A linear actuator turns a simple 12-volt supply into straight-line pushing and pulling motion, and this DC HOUSE model aims at the middle of that market: a 1000N (225 lb) force rating, a comparatively quick 14 mm/s travel speed, and a sealed aluminum alloy housing. This guide walks through its published specifications, the jobs it fits, and the points worth checking before wiring one into a project.
The listing pairs the actuator with mounting brackets and builds in a limit switch that cuts the motor at the end of travel, so the rod stops on its own instead of straining against a hard stop. Below you will find the full spec table, who this unit suits, how it stacks up against typical alternatives in its class, and answers to the questions buyers ask most often.
As an Amazon Associate, we earn from qualifying purchases.
Quick answer
The DC HOUSE 12-inch linear actuator is a 12V DC unit rated at 1000N (225 lb) of push and pull force, with a fast 14 mm/s travel speed, a built-in limit switch and an IP54 aluminum housing. Mounting brackets are included, and it suits hatches, lids, coop doors and other mid-load automation jobs.
Key specs
| Specification | Detail |
|---|---|
| Brand | DC HOUSE |
| Model number | L11TGF1000NB300-T-1 |
| Stroke length | 12 inches (305 mm) |
| Maximum load | 1000N (225 lb), push and pull |
| Travel speed | 14 mm/s (0.55 in/sec) |
| Input voltage | 12 V DC |
| Maximum current draw | 3 A |
| Retracted length | 370 mm |
| Extended length | 620 mm |
| Housing material | Aluminum alloy |
| Protection rating | IP54 |
| Shaft diameter | 14 mm |
| Item weight | 2.95 lb (1.34 kg) |
| Limit switches | Built in, automatic shutoff at end of travel |
| Noise level | not stated |
| Duty cycle | not stated |
| Lead wire length | not stated |
| Warranty | not stated |
Who it’s for / who should skip it
Who it’s for
- Builders automating hatches, lids, doors, vents or small lifting platforms that stay within the 225 lb rating.
- Projects running on 12V DC power, such as vehicle, solar or battery setups, where a two-wire hookup keeps wiring simple.
- Outdoor-adjacent jobs that face dust and splashing water but not immersion, thanks to the IP54 housing.
- Anyone who values travel speed: at 14 mm/s this unit finishes a full stroke far sooner than the slower high-force models in its class.
Who should skip it
- Loads above 225 lb, or jobs that need a wide safety margin under the rating, call for a heavier actuator class.
- Continuous-duty work. The listing publishes no duty cycle figure, so plan on intermittent motion rather than nonstop cycling.
- Applications that need position feedback for a controller; the listing describes a plain two-wire unit with a limit switch and no feedback device.
- 24V systems, since this model is built for a 12V DC supply.
How it compares with typical alternatives
Most 12-inch actuators in this class force a trade between speed and strength. Heavy-duty models often move at roughly 5 mm/s while pushing several times the load, and compact micro actuators give up force in exchange for size. This DC HOUSE unit sits on the speed side of that trade: 1000N is a mid-level rating, while 14 mm/s is quick for a unit of this size, so it favors frequent, lighter motion over occasional heavy lifting.
Alternatives also differ in extras. Some actuators add a feedback potentiometer for position control, some carry higher sealing ratings for harsher washdown settings, and some ship as kits with a controller, remote and power supply in the box. This listing keeps the package simple: the actuator and its mounting brackets, with the 12V supply and control switch left to the buyer. That keeps the install uncomplicated, at the cost of more parts to source for a complete setup.
FAQ
How much weight can this actuator move?
The published maximum load is 1000N, or 225 lb, and the listing gives the same characteristics for pushing and pulling. Keep the working load at or under that rating, including the weight of anything the rod carries through the whole stroke.
How long does a full stroke take?
The stroke is 12 inches and the published travel speed is 14 mm/s (0.55 in/sec), so one full extension takes a little over twenty seconds. The built-in limit switch cuts power automatically at each end of travel.
Can it work outdoors?
The aluminum alloy housing carries an IP54 rating, which the listing describes as sealed against dust, water and corrosion and suitable for outdoor use. That covers rain and splashing; it does not cover immersion, so mount it where standing water cannot pool around it.
What do I need to power it?
A 12V DC supply sized for a maximum draw of 3 amps. The red lead connects to the positive post and the black lead to the negative post, per the listing’s installation notes. A switch or controller for direction changes is a separate item.
Final verdict
For mid-load automation on a 12V system, this DC HOUSE actuator offers a sensible balance: enough force for hatches, lids and light lifting, faster travel than most rivals in its class, a sealed housing, and brackets in the box. Buyers who confirm the 225 lb ceiling, the 370 mm retracted length, and the need for a separate supply and switch will find it a straightforward fit. Heavier, wetter or feedback-driven jobs belong to other actuator classes.
Related articles
