Key takeaways
- Anyone powering ham radio gear, LED or CCTV installs, or automotive electronics testing is best served by a fixed-voltage, high-current switching supply…
Anyone powering ham radio gear, LED or CCTV installs, or automotive electronics testing is best served by a fixed-voltage, high-current switching supply such as those from Samlex, Astron, or Mean Well, while a hobbyist who wants adjustable voltage and current on a switching chassis should look at an adjustable bench-style switching supply from Korad, Rigol, or Siglent instead.
A switching bench power supply regulates its output using a high-frequency switching converter rather than a large mains transformer and linear pass transistor, which makes it lighter, smaller, and generally cheaper per watt than an equivalent linear supply. The trade-off reviewers consistently report is higher output ripple and electrical noise, which matters for sensitive analog, audio, or RF receiver work but is largely irrelevant for charging batteries, running motors, powering LED strips, or running most digital and radio-transmitting equipment.
What to Check Before Buying
- Fixed-voltage vs. adjustable: Many switching supplies are built for one fixed voltage (commonly 12V or 13.8V for ham radio and automotive electronics), while bench-style switching supplies offer a dial-adjustable range similar to a linear supply but in a lighter chassis.
- Continuous vs. surge current rating: Makers typically list both a continuous current rating and a higher short-term surge rating; radio transmitting equipment in particular can draw well above its average current during transmit bursts, so checking the surge rating against your equipment’s peak draw matters.
- Output ripple and noise: The datasheet lists ripple in mV; this is the main performance gap versus linear supplies and is worth checking against your specific application’s sensitivity.
- Fan noise and cooling style: Many switching supplies use a thermostatically controlled fan that only spins up under load; reviewers note some units run silent at idle and audible only near full load, which matters for a supply kept on a desk rather than in a rack or garage.
- Protections: Overcurrent, overvoltage, and thermal shutdown protection are standard on reputable units; confirm these are explicitly stated rather than assumed on lower-cost imports.
- Connector type: Fixed-voltage radio and automotive supplies commonly use binding posts or Anderson Powerpole-style connectors rather than banana jacks; confirm the connector matches your existing cabling or adapter plans.
Picks by Use Case
Best for ham radio and two-way radio equipment
Samlex and Astron both sell switching supplies specifically marketed for amateur radio use, typically fixed at 13.8V with high continuous and surge current ratings sized for transceiver transmit bursts. Astron’s switching lineup is a newer alternative to the company’s long-standing linear supplies, and reviewers report the switching versions run noticeably lighter and cooler for the same current rating.
Best for LED, CCTV, and general 12V DC projects
Mean Well’s enclosed switching supplies (commonly found in RS and LRS series-style product lines) are widely used in LED lighting, CCTV, and general 12V/24V DC project power, and are chosen by installers for their compact size, industrial-grade reliability ratings, and competitive cost per watt compared with linear alternatives.
Best adjustable bench-style switching supply
For hobbyists who want dial-adjustable voltage and current but in a lighter chassis than a linear bench supply, Korad and other bench-equipment makers sell switching-based adjustable supplies that cover a similar 0-30V-class range to their linear counterparts at a lower weight and often lower cost.
Best programmable switching supply for test and automation
Rigol and Siglent both offer programmable DC supplies built on switching architectures with USB/LAN control and list-mode sequencing, aimed at product testing and QA environments that need automated voltage/current profiles without the size and weight of an equivalent linear instrument.
| Type | Best for | Key stated specs | Limits |
|---|---|---|---|
| Fixed 13.8V radio supply (Samlex, Astron) | Ham radio and two-way radio transceivers | High continuous and surge current ratings, fixed voltage | Not adjustable; single-purpose voltage output |
| Enclosed 12V/24V supply (Mean Well) | LED lighting, CCTV, general DC projects | Industrial reliability ratings, compact enclosed chassis | Typically fixed voltage, minimal front-panel display |
| Adjustable bench switching supply (Korad and similar) | Hobby electronics wanting a lighter adjustable supply | Dial-adjustable voltage/current, 0-30V class range | Higher ripple than a comparable linear bench supply |
| Programmable switching supply (Rigol, Siglent) | Automated test sequences, QA labs | USB/LAN control, list-mode sequencing | Higher cost than basic adjustable or fixed-voltage units |
Fit and Compatibility Notes
Confirm the connector style on a fixed-voltage radio or automotive supply matches your equipment’s power cable; many radios ship with Anderson Powerpole connectors while some supplies use binding posts, requiring an adapter cable. Check the surge current rating against your equipment’s peak draw, not just its average draw, since radio transmitters and motor-starting loads can briefly pull well above their steady-state current. For installations near sensitive radio receivers, be aware that switching supplies can introduce RF noise that some reviewers report interferes with nearby receiver equipment; shielded or well-filtered units and physical separation from antennas and receivers help minimize this.
Pick This If…
| Situation | Recommended type |
|---|---|
| Powering a ham radio or two-way radio transceiver | Fixed 13.8V switching supply from Samlex or Astron |
| Installing LED lighting, CCTV, or general 12V/24V DC equipment | Enclosed switching supply from Mean Well or similar industrial makers |
| Hobby electronics needing adjustable voltage in a light chassis | Adjustable bench-style switching supply (Korad and similar) |
| Running scripted QA or production test sequences | Programmable switching supply from Rigol or Siglent |
| Sensitive analog, audio, or RF receiver work | Consider a linear supply instead for lower ripple and noise |
Alternatives Worth Considering
- A linear bench power supply: For sensitive analog, audio, or RF receiver circuits where output noise matters most, a traditional linear supply trades size and weight for lower ripple.
- A combined power supply/charge controller: Some switching supplies marketed for radio use also include a battery charging/maintenance mode, useful for stations that keep a backup battery on standby.
- A used or surplus industrial switching supply: Decommissioned industrial or telecom switching supplies, available through surplus electronics resellers, can offer high current ratings at a lower cost than new consumer-branded units, though documentation and support are usually minimal.
Frequently Asked Questions
Is a switching power supply reliable enough for daily use?
Yes; reputable switching supplies from established industrial and radio-equipment makers are built for continuous daily operation and are widely used in commercial LED lighting, CCTV, and radio base-station installations. Reliability depends more on buying from a reputable maker with stated protection circuits than on the switching topology itself.
Will a switching supply cause interference with my radio?
It can, particularly with cheaper or poorly filtered units; some reviewers report audible noise on receive when a switching supply is placed close to a radio and antenna. Well-shielded units from established radio-equipment makers, physical separation from the antenna, and good cable routing generally minimize this.
Do I need surge current capacity or just continuous current?
Both matter, but for equipment with bursty peak draw, such as a radio transmitter keying up or a motor starting, the surge rating is what determines whether the supply can handle that moment without dropping voltage or shutting down. Check your equipment’s peak draw specification, not just its average, against the supply’s surge rating.
Can I use a switching supply to charge batteries?
Some switching supplies include a dedicated charging or float-charge mode suitable for maintaining a backup battery, while a plain fixed-voltage supply without that mode is not designed for proper battery charging and can overcharge or undercharge a battery over time. Check the specific unit’s documentation for a stated charging mode before using it that way.
Why is a switching supply so much lighter than a linear one with the same rating?
A linear supply’s weight comes mostly from its large mains-frequency transformer, while a switching supply converts power at a much higher frequency, which allows a far smaller and lighter transformer and overall enclosure for the same output rating. This is also part of why switching supplies are generally cheaper to manufacture at higher power levels.
Is an adjustable switching bench supply as accurate as a linear one?
Modern adjustable switching bench supplies from reputable makers are generally accurate enough for most hobby and general test use, though their datasheets typically show somewhat higher ripple and noise figures than an equivalent linear design. For most digital, LED, and general prototyping work this difference is not noticeable in practice.
Related articles
- Best AC DC Bench Power Supply: Picks and What to Look For (2026)
- Best Bench Power Supply Unit: Picks and What to Look For (2026)
- Best High Current Bench Power Supply: Picks and What to Look For (2026)
- Best Switching DC Power Supply: Picks and What to Look For (2026)
- Best GPU for Cuphead: Picks and What to Look For (2026)
- Best CPU for Rtx 4080 Super: Picks and What to Look For (2026)