Updated Nov 16, 2026· 7 min read

Key takeaways

  • For most desktop builders the Arctic MX-6 is the safest all-round thermal paste, Noctua NT-H2 suits people who want a paste meant to stay on the processor…

For most desktop builders the Arctic MX-6 is the safest all-round thermal paste, Noctua NT-H2 suits people who want a paste meant to stay on the processor for years, and Thermal Grizzly Kryonaut is the usual choice for overclockers chasing the last couple of degrees. All of these fit comfortably under 50 dollars, and the differences between them are small compared with getting the application right, so the best choice is the one that matches how often you plan to reapply it and how comfortable you are with a thicker or thinner paste.

Our top picks

As an Amazon Associate we earn from qualifying purchases at no extra cost to you.

What thermal paste does and what to expect

A processor’s heat spreader and a cooler’s base are never perfectly flat. Thermal paste fills the microscopic gaps so heat moves from the chip to the cooler efficiently. It is not a cooling device by itself, and a thin, even layer matters more than the brand. Independent testers who compare pastes typically find differences of only a few degrees between good products, and reviewers quoted in roundups say that a decent paste such as the MX-6 comes within a couple of degrees of the more expensive enthusiast compounds. Paste cannot fix a poorly mounted cooler, so focus on mounting pressure and flatness first.

Published conductivity numbers vary between sources and are not a reliable predictor of real results. Arctic and Noctua both decline to publish a thermal conductivity value for their pastes, while other listings give figures such as 12.5 W/mK for Kryonaut and 14.2 W/mK for Kryonaut Extreme. Treat those numbers as marketing indicators and look at measured temperature differences instead.

At a glance: thermal pastes worth considering

Paste Best for Key stated specs Limits
Arctic MX-6 Most users, gaming and daily PCs The maker says it is neither electrically conductive nor capacitive; high viscosity of 45,000 poise; operating range of -50 to 150 degrees C; packs of 2, 4 and 8 g in syringes Thick; cannot be spread with a spatula, so use a dot or line
Noctua NT-H2 Long-lasting installs, silent builds The maker lists non-conductive, non-corroding, -50 to +200 degrees C, 3.5 g tube, up to about 3 applications on large CPUs, and up to 5 years on the processor Costs more per gram; no conductivity figure published
Thermal Grizzly Kryonaut Overclocking and high-power CPUs Listings show 12.5 W/mK; non-conductive paste in a small syringe Small tubes; may need reapplication after a long time
Thermal Grizzly Kryonaut Extreme Enthusiasts who want a higher listed spec Listings show 14.2 W/mK and a wide temperature range Premium price for a small quantity
Arctic MX-4 Low cost, older proven option The previous generation to MX-6, widely used Reviewers report that MX-6 is a few degrees cooler in some tests
Honeywell PTM7950 Maintenance-free phase-change pad Used as a replacement for paste on some CPUs and GPUs, per roundups Requires careful application and is a different product type

Choosing by what matters to you

Safety: non-conductive vs conductive

Non-conductive pastes such as MX-6, NT-H2 and Kryonaut are forgiving. If a little spreads onto the circuit board around the CPU socket it will not short components. Liquid metal compounds such as Thermal Grizzly Conductonaut do conduct electricity and can react with aluminum, so makers include warnings and they are best left to experienced builders. If you are unsure, choose a non-conductive paste.

Longevity and pump-out

Some pastes dry out or migrate away from the center of the chip after months of heat cycles. Noctua says its NT-H2 can stay on a processor for up to five years, and Arctic describes MX-6 as non-drying and non-bleeding. Those statements come from the makers, so treat them as intentions rather than guarantees. If you want to avoid reapplying, pick a paste with a long stated service life.

Ease of application

MX-6 is thick, and the maker notes that it cannot be applied with a spatula. A pea-sized dot or a line is the usual approach. Kryonaut is thinner and spreads more easily. Reviewers sometimes recommend thicker pastes for beginners because they are less messy, while thin pastes can be easier to spread evenly.

Quantity

A 2 g tube is enough for one or two applications on a typical CPU. If you build PCs often, repaste a laptop or graphics card, or want to keep a spare, choose a larger tube such as the 8 g MX-6 or the 3.5 g NT-H2. Noctua states that a tube covers about three large CPUs, around 15 medium ones and about 20 small ones.

Authenticity

Counterfeit pastes exist. Arctic mentions an authenticity verification system on its packaging. Buy from the maker or an authorized seller, and examine packaging for damage.

Budget tiers

Low budget

The Arctic MX-4 and similar value pastes work well and are the cheapest way to repaste. They suit older builds and quick maintenance, and the temperature difference to the current best pastes is small.

Mid-range

The Arctic MX-6 sits here and is the most frequently recommended choice. One roundup reports that on a Ryzen 7 7800X3D the MX-6 ran about 3 degrees cooler than MX-4 in a Cinebench loop, which is a modest but real gain.

Premium

Kryonaut, Kryonaut Extreme and NT-H2 form the premium tier, with tests showing small advantages at high power levels. Another roundup shows Kryonaut about 2 degrees cooler than MX-6 on an overclocked i9-14900K, though several guides stress that the gap is small for typical users.

How to apply thermal paste safely

  1. Power down, switch off the power supply and unplug the cable before removing a cooler.
  2. Twist the cooler gently to break the bond before lifting it, since the paste can hold it in place.
  3. Clean the processor and the cooler base with isopropyl alcohol (90 percent or higher) and a lint-free cloth. Let them dry fully.
  4. Apply a pea-sized dot at the center of the processor, or follow the maker’s recommended pattern for large chips. Arctic and Noctua publish illustrated guides.
  5. Lower the cooler straight down and tighten the screws in a cross pattern. Do not slide the cooler around.
  6. Wipe away any excess outside the contact area with a dry cloth, and keep paste away from the socket pins and the board.
  7. Boot the system and monitor temperatures to confirm the cooler is seated correctly.

Keep paste away from children and pets, wash your hands after handling it, and follow the maker’s safety notes. If paste contacts your skin or eyes, rinse and consult the safety data sheet.

Pick X if you need Y

If you need Pick Reason
A reliable all-round paste Arctic MX-6 Non-conductive, widely recommended, good balance
A paste you will leave for years Noctua NT-H2 The maker states up to five years on the processor
The best temperatures from non-metal paste Thermal Grizzly Kryonaut or Kryonaut Extreme Topped some benchmarks in reviewers’ tests
The cheapest sensible paste Arctic MX-4 Proven older option
A pad instead of paste for a GPU or laptop Honeywell PTM7950 Phase-change pad popular for maintenance-free use

Alternatives

  • Thermalright TF7 and TF8. Thermalright pastes appear in some comparison tables, with one roundup placing the TF7 ahead of NT-H2 and MX-6 in a particular test. Independent coverage of the TF8 is limited.
  • Pre-applied paste. Many coolers ship with paste already applied, which is adequate for a first install.
  • Thermal pads. Useful for memory chips and voltage regulators on graphics cards, but not a replacement for paste on a processor.

Signs it is time to repaste

Idle and load temperatures that creep upward over months, fans that spin harder than they used to, or sudden throttling in a game are the usual signs. Before repasting, clean the dust from heatsink fins and fans, since dust is a more common cause than dried paste. Repaste when you move a cooler to a new processor, after any cooler removal, or when a used system has an unknown history. For laptops, consult the maker’s service guide first, since opening the chassis can affect warranty terms.

Frequently Asked Questions

How much thermal paste should I use?

A pea-sized dot at the center is the standard approach for most desktop CPUs. Too much paste can squeeze out and make a mess, while too little can leave gaps. Follow the application guide from the paste maker for large processors.

How often should I replace thermal paste?

Many people repaste every few years or when temperatures rise noticeably. Noctua states that NT-H2 can stay on a CPU for up to five years. If your temperatures are stable, there is no need to replace paste on a schedule.

Is liquid metal worth it?

It can lower temperatures further, but it is electrically conductive and can damage aluminum or stain surfaces. For most people the small gain is not worth the risk. If you consider it, read the maker’s instructions carefully.

Can I mix different pastes?

It is better to clean off the old paste completely before applying a new one. Mixing can create uneven layers. Use isopropyl alcohol and a lint-free cloth to remove the old compound.

Does expensive paste make a big difference?

Usually not. Roundups report gaps of only a few degrees between good pastes, and correct cooler mounting often matters more. Choose a reputable paste and spend the rest on better cooling or fans.

Is thermal paste safe for a graphics card?

Many people repaste graphics cards, but doing so may void a warranty and requires disassembling the card. Follow your card maker’s guidance and consider a professional service if you are not confident.

D
Dũng Trọc Hà Đông
We compare specs, materials and verified owner reviews before a product earns a spot. Rankings are never paid.
Affiliate disclosure. As an Amazon Associate we earn from qualifying purchases at no extra cost to you. Prices accurate as of the date shown.
Best Thermal Paste under $50: Picks and What…Check price on Amazon