Key takeaways
- A 4-gang meter socket suits property owners feeding four separate utility meters from one service point, such as a fourplex, a small strip of row houses…
A 4-gang meter socket suits property owners feeding four separate utility meters from one service point, such as a fourplex, a small strip of row houses, or a mixed-use building with four tenants; the right choice depends mainly on amperage per gang, ringless-versus-ring-type metering, and whether the local utility requires a specific listed model.
Meter socket equipment of this kind is sold almost exclusively to licensed electricians, property developers, and utility-approved installers, because the final installation must match both the National Electrical Code and the serving utility’s own metering specifications. This guide covers what to compare before buying, where a 4-gang unit fits against other gang counts, and the questions worth asking an electrician or the utility before placing an order.
What a 4-Gang Meter Socket Does
A gang meter socket, sometimes called a meter stack or meter nest, groups multiple individual metering positions into one enclosure fed from a single service lateral or overhead drop. A 4-gang unit provides four separate metering compartments, each with its own socket for the utility’s meter and its own set of lugs feeding a breaker or disconnect for that unit. This differs from a single meter socket, which services one dwelling or tenant only, and from larger meter centers built for six, eight, or more positions.
Multi-gang equipment is typically installed at new multi-family construction, at conversions where a building is being split into separately metered units, or where a utility requires consolidation of multiple existing single meters into one bank for easier reading and maintenance access.
Specs That Matter Before Buying
Amperage rating per position is the first spec to confirm; common ratings for multi-gang residential-style sockets run in the 100 to 200 amp range per position, and the enclosure’s main bus must be rated to carry the combined load of all four positions, not just one. Ringless versus ring-type construction affects how the meter mounts and how the utility seals it; most utilities today specify ringless designs, but older service areas may still require ring-type, so confirming with the local utility before ordering avoids a mismatch. Overhead versus underground service entry changes which hub and conduit openings the enclosure needs, and some units are configured for one or the other rather than both.
UL listing is a baseline requirement for any meter equipment installed under the National Electrical Code, and many utilities maintain their own approved-equipment list that is narrower than UL listing alone; checking that list before buying is the single most common step installers skip and later regret.
At a Glance: Multi-Gang Meter Socket Tiers
| Tier | Best for | Typical stated amperage per position | Key limit |
|---|---|---|---|
| Residential 4-gang, ringless | Fourplexes, small multi-tenant buildings | 100-125 amps per position | Main bus amperage caps total combined load |
| Residential 4-gang, ring-type | Utility areas still requiring ring-seal meters | 100-200 amps per position | Fewer makers still stock ring-type in this gang count |
| Commercial-duty 4-gang | Mixed-use or light commercial tenants | 200 amps per position | Larger enclosure footprint and heavier conduit needs |
| 4-gang with integral main disconnect | Utilities or jurisdictions requiring a single service disconnect | Varies by model | Higher upfront cost tier than disconnect-less models |
Installation and Code Compliance Notes
Only a licensed electrician should size conductors, set the main bus rating, and make the final service connection on gang metering equipment; the stakes of an undersized bus or an incorrect grounding and bonding setup are a fire and shock hazard, not a cosmetic issue. The National Electrical Code sets baseline clearance, grounding, and working-space rules around service equipment, and the local jurisdiction’s amendments on top of that code are what the inspector actually checks against. Utility sign-off is a separate step from code compliance; a unit can pass inspection and still be rejected by the utility if it is not on their approved list, so confirming utility approval before purchase, not after installation, avoids a costly swap.
Weatherproofing matters for any outdoor-mounted bank: look for a NEMA 3R rating at minimum for most outdoor installs, and ask the electrician whether the specific mounting location needs a higher rating due to coastal exposure, direct wash-down, or heavy snow load.
Pick the Right Configuration If…
| Situation | Suggested direction |
|---|---|
| Four residential units, standard suburban service | Residential 4-gang, ringless, 100-125 amp positions |
| Older service area that still requires ring-seal meters | Ring-type 4-gang, confirmed against the utility’s approved list |
| Mixed-use building with higher per-unit loads | Commercial-duty 4-gang at 200 amps per position |
| Jurisdiction requires one visible main disconnect for the whole bank | 4-gang model with an integral main disconnect |
| Fewer or more than four tenants | Step down to a 2 or 3-gang unit, or up to a 6 or 8-gang meter center |
Alternatives Worth Comparing
Buyers with only two or three metered units are usually better served by a 2-gang or 3-gang socket, which costs less and takes up a smaller footprint than a 4-gang unit run under capacity. Properties expecting to grow past four tenants, or that already have five or more, should look at modular meter centers built in 6, 8, or 12-position configurations, which several of the same manufacturers that build 4-gang sockets, including Milbank, Eaton, and Siemens, also offer in their metering equipment lines. Where local code allows it, some small multi-family projects use individual single-gang meter sockets mounted side by side instead of one combined enclosure; this costs more in enclosures and labor but can simplify future meter swaps or utility changes one unit at a time.
Lead Time and Ordering Notes
Multi-gang meter equipment, especially configurations with an integral main disconnect or a less common amperage combination, is often a special-order item rather than a shelf stock item at a typical supply house, and lead times can run several weeks depending on the manufacturer’s current production schedule. Builders working to a fixed project timeline should confirm lead time with the supplier early in the planning process, ideally before the service entrance rough-in stage, since a delayed meter bank can hold up the final electrical inspection and utility connection on an otherwise finished project. Ordering the base model and any matching accessories, such as a weatherhead, hub kit, or grounding bar, from the same manufacturer line also reduces the chance of a fit mismatch at installation compared to mixing parts from different suppliers.
Frequently Asked Questions
Can I install a 4-gang meter socket myself?
This is service-entrance equipment, and in nearly every jurisdiction the final connection to utility power must be made or signed off by a licensed electrician, with the utility itself often required to make or inspect the final meter-side connection. Treat this as licensed-electrician work, not a do-it-yourself project.
How do I know what amperage rating I need per position?
An electrician calculates each unit’s expected load based on square footage, appliances, and any electric heating or cooling, then sizes the position and the main bus accordingly. Guessing at amperage risks either an undersized bus that trips or overheats, or paying for capacity that is never used.
Does the utility need to approve the meter socket before I buy it?
Most utilities maintain an approved-equipment list for metering gear, and installing a unit that is not on that list can mean the utility refuses to set meters until it is replaced. Confirming the exact model against the serving utility’s current list before ordering is a required step, not an optional one.
What is the difference between ringless and ring-type meter sockets?
Ring-type sockets use a separate metal ring to seal the meter in place, while ringless sockets rely on the meter’s own base and a tamper seal without a separate ring. Most utilities have shifted toward ringless designs, but some service areas still specify ring-type, so this is a utility-specific question, not a personal preference.
Do I need a main disconnect built into the meter bank?
Some jurisdictions require a single, readily accessible disconnect for the entire service, which some 4-gang meter banks include as an integral main breaker or switch; others leave disconnecting means to individual unit panels. Check local code and utility requirements before choosing, since this affects both the model selected and the inspection outcome.
What enclosure rating do I need for an outdoor installation?
A NEMA 3R rating is the common baseline for outdoor service equipment exposed to rain and snow. Coastal, industrial, or heavy wash-down locations may call for a higher rating; an electrician familiar with the site conditions can confirm what the location actually needs.
Related articles
- Best 6 Gang Meter Base: Picks and What to Look For (2026)
- Best Marine Waterproof Plugs and Sockets: Picks and What to Look For (2026)
- Best Air Filters That Remove Mold: Picks and What to Look For (2026)
- Best 240V to 110V Step Down Transformer: Picks and What to Look For (2026)
- Best Wheelchair Ramps for Home: Picks and What to Look For (2026)
- Best LED Bathroom Vanity Lights: Picks and What to Look For (2026)